Set of high quality Ergal straight cut timing gears to replace the timing chain and sprockets. All lightweight alloy gears, these are a good performance upgrade that are significantly lighter than the original chain and sprockets

This is a popular modification which improves high RPM reponse and eliminates backlash and slack in the engine timing resulting in improved perfomance - and you'll never need to retension your cam chain again! See this article for advice on fitting timing gears

 Sorry, this part is no longer available.

Pair of chromed Hepco and Becker pannier rails for Hepco and Becker panniers

Pair pannier racks

 This part is available by special order, request a quote

Tough Xplorer top box / top case to match Hepco and Becker Xplorer panniers, ideal for enduro touring. Extremely endurable combination of aluminium sheet and coloured shock-resistant plastic.

• Completely waterproof thanks to special seals
• Made of 1.5 mm thick plate aluminum and highly
impact-resistant plastic molding
• Absorbs impacts and ground contact
• Stable metal locks, integrated carrying handles
• Case and top case available with simultaneous
locking (please specify when ordering)
• Takes a full-face helmet
• Innovative side hinged design
• Fits all H&B rear racks and aluminum racks

 This part is available by special order, request a quote

Set of high quality Ergal spur cut timing gears to replace the timing chain and sprockets. The crankshaft gear is steel, the oil pump and camshaft gears are alloy. These spur gears are much quieter than straight cut gears

This is a popular modification which improves high RPM reponse and eliminates backlash and slack in the engine timing resulting in improved perfomance - and you'll never need to retension your cam chain again! See this article for advice on fitting timing gears

 Sorry, this part is no longer available.

Tough Xplorer top box / top case to match Hepco and Becker Xplorer panniers, ideal for enduro touring. Extremely endurable combination of black anodised aluminium sheet and coloured shock-resistant plastic.

• Completely waterproof thanks to special seals
• Made of 1.5 mm thick plate aluminum and highly
impact-resistant plastic molding
• Absorbs impacts and ground contact
• Stable metal locks, integrated carrying handles
• Case and top case available with simultaneous
locking (please specify when ordering)
• Takes a full-face helmet
• Innovative side hinged design
• Fits all H&B rear racks and aluminum racks

 This part is available by special order, request a quote

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 3 Ohm 12 volt coils and can be used to replace points or Motoplat ignition on models with Saprisa charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA31165

 This part is available by special order, request a quote

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500

 This part is available by special order, request a quote

Complete sump kit which moves the oil filter out from within the sump to a recess under the sump. This simplifies and speeds up oil changes because the sump no longer needs to be removed. Oil cooling is also improved because oil will cool through the body of the filter. The complete sump kit is a simple fit that will speed up oil changes and reduce the risk of stripping crankcase bolts through repeated sump removal. It is very similar to the arrangement on modern CARC models. Replaces sump extension ENA14002. Finished in silver this is a great upgrade for your Guzzi. Uses oil filter SIA14530

Depending on model you may need a longer dipstick e.g. ENA28495. You can calibrate the sump by adding 3l of oil and marking the position on the dipstick. Note that you need to transfer your oil pressure relief valve and the intake screen from your existing sump into this new one. Note also that the stamped steel covers on some oil pressure relief valves flare wider than others so you may need to make a little clearance in order to get the threads started. Also available at additional cost in black by special order - ENA14006

 This part is available by special order, request a quote

Complete sump kit which moves the oil filter out from within the sump to a recess under the sump. This simpifies and speeds up oil changes because the sump no longer needs to be removed. Oil cooling is also improved because oil will cool through the body of the filter. The complete sump kit is a simple fit that will speed up oil changes and reduce the risk of stripping crankcase bolts through repeated sump removal. It is very similar to the arrangement on modern CARC models. The kit consists of:

1. Deep sump casting (82mm deep) with all oil ways. Uses oil filter SIA14530
   Replaces sump extension ENA14002. Finished in black this is a great upgrade for your Guzzi

   Depending on model you may need a longer dipstick e.g. ENA28495. You can calibrate the sump by adding 3l of oil and marking the position on the dipstick. Note that you need to transfer your oil pressure relief valve and the intake screen from your existing sump into this new one. Note also that the stamped steel covers on some oil pressure relief valves flare wider than others so you may need to make a little clearance in order to get the threads started. Also available at additional cost in black to special order

    This part is available by special order, request a quote

   [ CLOSE WINDOW ]
   [ CLOSE WINDOW ]

Pair of black 30 litre Junior panniers to fit Hepco and Becker pannier frames (fitted as OE to many models). These are the classic Hepco and Becker pannier design.

• Unbreakable, special double walled shell made of impact resistant plastic which absorbs bumps and falls
• Completely waterproof thanks to special seals
• Fitted with rugged metal locks and an ergonomic carry handle
• Aerodynamic design
• Inner bags and accessories available

These are a great value pannier set which are quickly and securely fitted to any Moto Guzzi using Hepco pannier rails (available from Gutsibits). Their discreet and classic styling looks right on any Guzzi from the 1970's to the present day. Supplied with aluminium lock adapter plates and two lock keys. See LUA70129 and LUA70128 for Guzzi badges to fit these panniers. These panniers are compatible with the frames used for Hepco Classic panniers

 This part is available by special order, request a quote

[ CLOSE WINDOW ]
[ CLOSE WINDOW ]